TEST YOUR DEVICE BEFORE USING IT & TROUBLESHOOTING - INSTRUCTIONS

To ensure your device is kept within the guidelines for a (FREE) 30 day warranty replacement , please make sure to follow the steps below BEFORE USING YOUR DEVICE.


* Keep in mind that once you load your heating chamber with product, this automatically voids the warranty for a free replacement.HOWEVER, DO NOT FEAR because SMK24 does offer a ONE YEAR Replacement Program to purchase replacement parts for a 

deeply discounted price.

For more information or to order a replacement part,
 follow the link to our help desk and submit a request located at the bottom of this article.

          

TESTING YOUR DEVICE BEFORE USE 


STEP 1.
FULLY CHARGE THE BATTERY WHEN YOU FIRST RECEIVE IT:



Anywhere between 2-6 hours is recommended until the charger indicates a green, charged, light.



STEP 2.
UNLOCK YOUR BATTERY AFTER TAKING IT OFF THE CHARGER:



Most newer devices come with this feature; if your battery has this feature, unlock it by rapidly pressing the power button
5-7 times rapidly!








STEP 3.

ATTACH THE HEATING CHAMBER:

Remove the rubber mouthpiece and chamber connector (along with the ceramic filter, mesh filter, and spring located inside these parts) and attach only the ceramic heating chamber to your battery. 





STEP 4.
MAKE SURE YOUR CHAMBER COILS TURN RED:

Press and hold the power button while looking inside the barrel of your chamber. Your should expect see your chamber coils start to turn bright red, as shown above.
 

We have found that the following steps, if done correctly, will solve ALMOST all "issues" simply due to not having the PROPER CONNECTION between the battery disc and the heating chamber disc.

 *IF YOUR COIL DOES NOT TURN RED:
PRIOR TO CONTACTING CUSTOMER SUPPORT
PLEASE CAREFULLY FOLLOW THE TROUBLESHOOTING STEPS BELOW.


.
.

TROUBLESHOOTING INSTRUCTIONS CONTINUED BELOW

MAKE SURE TO TAKE THE NEXT STEPS CAREFULLY AND GENTLY.
IF YOU HAVE ANY QUESTIONS PLEASE CONTACT US BEFORE YOU CONTINUE.
WE ARE NOT HELD RESPONSIBLE FOR DAMAGE CAUSED BY USER ERROR.

.
.
.

 

Step One: Battery

__________________________________________________

At the top of the battery you will see a SOLID ROUND DISC sitting atop.


You should have enough space in between the wall of the battery and the disc to fit a compact packing tool (or something small such as a paper clip) Please have your tool ready.


Some devices may have the disc below the pin.
Do not fear, please follow the same instructions. 


 
STEP 1:
 Clean this round disc of any reside. You may use a cotton swab with 90% alcohol to swab it. 

STEP 2:
Place the rounded end of your compact packing tool (or something small such as a paper clip) between this round disc and wall of the battery.

STEP 3:
Gently push towards the center which will bring one side slightly up (about a millimeter) Go around the rest of the disc just making it even.

STEP 4:
Once you've raised the discs in the battery enough (about a millimeter), set it down and proceed to follow the next step.
 
.
.
.
.

 
Step Two: Ceramic Heating Chamber
__________________________________________________

With ONLY the chamber part in your hand, the MOUTHPIECE SIDE is facing UP
Tilt the mouthpiece AWAY from you until you are looking at the BOTTOM of the chamber (the side that is ALL metal and connects with the battery).
Here you will see a solid round metal disc right in the center like shown in the photo above.
This is the disc in the ceramic heating chamber.

 
Detach the ceramic heating chamber from the battery for the next steps.

The goal of this step is to RAISE this disc in the event that it is too compressed. Sometimes these discs are too compressed during the manufacturing process and initially will need to be raised before use.

 

STEP 1:
Clean this round disc of any reside. You may use a cotton swab with 90% alcohol to swab it. 
 
STEP 2:
Place the rounded end of your compact packing tool (or something small such as a paper clip) against this round disc and wall of the ceramic heating chamber.
 
STEP 3:
Slide the end of your tool up, toward the tip of this pin until you feel a silicone band (slightly visible in the photo above - it is better felt than seen.)
 
STEP 4:
Gently wedge against this silicone band towards the center which will bring one side slightly up (about a millimeter). Go around the rest of the disc just making it even.
 
STEP 5:
Once you've raised the discs enough (about a millimeter), connect the ceramic heating chamber to the battery, both which are now cleaned and raised. Press and hold the power button and check if this fixed any problem you were experiencing.

.
.
.
.

 

Step Three: Premium E-liquid Attachment(s)

__________________________________________________




STEP 1:

Clean the round disc of any reside from the battery as listed in step one. You may use a cotton swab with 90% alcohol to swab it. 

STEP 2:
Set the battery down and get that cartridge you just set down and keep it flipped upside down (opposite of the way you would attach it to the battery - like shown in the photo above).

STEP 3:
Unscrew the rigid bottom part and set that rigid part down (the base with the atomizer rod sticking up). Now, with the glass part that is still in your hands, empty any juice left and take a skinny q-tip and gently clean the mouth hole (straight through the middle). You should be able to q-tip the majority of the juice out of there.
 
STEP 4:
Set the glass part down and pick up the rigid bottom part you just unscrewed in the step before (the part with the atomizer sticking out of it). Now, you want to unscrew that rod (atomizer) from the base and take a tissue and gently wipe down both of those parts down.
!! IMPORTANT: When reattaching the atomizer back to the base, you must make certain to twist it on tightly because while unscrewing the battery from the cartridge over and over again before your next fill, this can cause that atomizer to become loose and leak on your device.
STEP 5:
BEFORE you reconnect the base with the glass, TO FILL THE CARTRIDGE, you DO NOT want to pour any e-liquid in that middle hole! (That center hole is designed to allow airflow.)

STEP 6:
With the cartridge upside down tilt it sideways and fill the juice into the glass. When you have filled it, insert the rod part into the mouth hole and reattach the base. When you flip it the juice should NOT escape from inside that glass part and NOT get into your mouth.


NOTE: Standard cartridges are NOT filled upside down. -->







If after completing these steps you are still experiencing any issues or would like more information or assistance please do not hesitate to contact us at our customer support line: (305) 600-5300 during regular business hours, which are Mon-Fri 9:30AM-5:30PM (EST) so we can assist you in troubleshooting your device and proceed further if necessary.

You can also submit a request to our 
Customer Support department and a Customer Support Agent will be able to assist you in the order in which the requests are received to make your situation is handled timely and appropriately.

Did you find this article helpful?